At our school there are always power outages. Sometimes they last only a few seconds, sometimes several hours. To ensure that our IT infrastructure does not suffer from this, we have installed a UPS for our servers and network devices. These help to bridge short power outages (up to 1 hour) or fluctuations in current. For any lengthy outages, we automatically shut down our servers when the UPS reaches critical battery level. For this we use NUT (Network UPS Tools). Our setup consists of the following components: as UPS server or master Raspberry Pi Liebert GXT4 UPS Server as clients or slaves Set up UPS in NUT on the Raspberry Pi For the Raspberry Pi we use the standard . Note that SSH has not been enabled by default since 2016. The different ways to reactivate SSH are . After reactivating SSH, you can now log on to the Raspberry Pi (the IP of the Raspberry Pi can be found out from a computer in the same network with or you can connect a monitor and keyboard). We will need the IP later, so it makes sense to give the Raspberry Pi a static IP. Raspian Stretch Lite Image documented here avahi-browse -ar Next we install the NUT server with sudo apt-get install nut-client nut-server usbutils If the UPS is connected via USB (as in our case), you can check with if it was detected. This is what the output on the Raspberry Pi looks like: lsusb $ lsusbBus 001 Device 004: ID 10af: 0000 Liebert Corp. UPSBus 001 Device 003: ID 0424: ec00 Standard Microsystems Corp. SMSC9512/9514 Fast Ethernet AdapterBus 001 Device 002: ID 0424:9514 Standard Microsystems Corp.Bus 001 Device 001: ID 1d6b: 0002 Linux Foundation 2.0 root hub In the first line you can see that our Liebert UPS has been recognized. Now we have to configure our UPS in the file . For our UPS, the entry looks like this: /etc/nut/ups.conf [gxt4]driver = usbhid-upsport = carproductid = 0000desc = “Emerson Liebert GXT 4” On the Network UPS Tools website, you will find a list of all supported UPS and which driver works best. Next, we want to test whether the settings are correct, the UPS Daemon can communicate with the UPS. For this purpose we start with upsd sudo upsdrvctl start A successful output should look something like this: Network UPS Tools — UPS driver controller 2.7.2Network UPS Tools — Generic HID driver 0.38 (2.7.2)USB communication driver 0.32Using subdriver: Belkin HID 0.16 NUT contains a small program to test the communication with UPS. It is called and outputs all readable UPS parameters. upsc $ upsc gxt4Init SSL without certificate databasebattery.charge: 100battery.charge. low: 20battery.charge. warning: 0battery.type: PbAcbattery.voltage: 0.0battery.voltage. nominal: 0.0device.mfr: Emerson Network Powerdevice.model: Liebert GXT4device.serial: 1607000060AFC23device.type: upsdriver.name: usbhid-upsdriver.parameter. pollfreq: 30driver.parameter. pollinterval: 2driver.parameter. port: autodriver.parameter. productid: 0000driver.version: 2.7.2driver.version. data: Belkin HID 0.16driver.version. internal: 0.38ups.mfr: Emerson Network Powerups.model: Liebert GXT4ups.productid: 0000ups.serial: 1607000060AFC23ups.status: OL CHRGups.vendorid: 10af Now our UPS is successfully installed. Next we set up the NUT server, the UPS monitor and two more users for the master and the slaves. upsmon Configuring the NUT Server In we specify that the Raspberry Pi is our master: /etc/nut/nut/nut.conf MODE=netserver The UPS Daemon ( ) is running on the NUT server. It is responsible for the (physical) connection to UPS. The individual clients/slaves use the to access the status of the UPS. In this way, multiple clients can always know the status of the UPS and, if necessary, initiate shutdown when UPS delivers the status “On Low Battery”. upsd upsmon In order for our NUT server to be accessible from the net, the following lines have to be added to (adjust IP please): /etc/nut/upsd.conf LISTEN 127.0.0.0.1LISTEN 192.168.1.2 #IP of the Raspberry Pis Next, we define the users that a client can use to log on to the master (in the file ): /etc/nut/upsd.user [upsmaster]password = secretupsmon master [upremote]password = secretupsmon slave In order for to monitor the UPS, we now need to add a final entry in : upsmon /etc/nut/upsmon.conf MONITOR gxt4@localhost 1 upsmaster secret master In order to know if all services are running correctly, you can check the status of the server and the local clients on the Raspberry Pi (because it should be shut down when there is no more power) with the following commands: $ sudo systemctl status nut-server$ sudo systemctl status user-client Now our master is set up and the clients or slaves can be configured. Set up clients/slaves (e. g. server, other computers) First, the necessary packages must be installed on a client: sudo apt-get install nut-client This time we only have to edit two files. In we set the mode: /etc/nut/nut/nut.conf MODE=netclient Then we need to tell which UPS to monitor (in ): upsmon /etc/nut/upsmon.conf MONITOR gxt4@192.168.1.2 upsremote secret slave The IP and password have to be adjusted. Please also note the slave at the end! Finally, restart the corresponding service and check that everything is running: $ sudo systemctl restart user-client$ sudo systemctl status user-client Congratulations! Now everything should be set up, but how can you test that it really works? Testing shutdown The following command triggers the shutdown signal (as it would be in the event of a power failure): $ sudo upsmon -c fsd Conclusion NUT is another great open source project that allows very flexible customizations. contains many more (complex) application scenarios. While I’m writing this article, we’re out of power again and all our servers have been shut down :) This PDF This post was first published on . openschoolsolutions.org Follow @OpenSchoolZ on Twitter.

Twitter

Too Long; Didn't Read

Get VPN and ad blocker with a single subscription	

How to Shutdown Your Servers In Case of Power Failure — UPS, NUT & Co.

Too Long; Didn't Read

Company Mentioned

Open School Solutions

Share Your Thoughts

About Author

TOPICS

THIS ARTICLE WAS FEATURED IN...

How to Shutdown Your Servers In Case of Power Failure — UPS, NUT & Co.

Too Long; Didn't Read

Company Mentioned

Open School Solutions

Share Your Thoughts

About Author

TOPICS

THIS ARTICLE WAS FEATURED IN...

RELATED STORIES